• sales@alatuji.com

     

  • 021 8690 6777
    021 8690 6770
  • 0812 9595 7914 (Mr. Parmin)
    0813 1066 1358 (Ms. Eki)
    0812 8333 5497 (Mr. Muslim)
  • 0812 1248 2471 (Mr. Alfin)
    0819 4401 4959 (Mr. Arya)

AU - 1005 A TENSILE STRENGTH TESTER (Electro-Mechanical)

 

This instrument measures the maximum tensile force the test piece will stand before it breaks and the elongation at the moment of rupture. It is used for determining the tensile strength and stretch at break of the paper, board, metal foil, textile and plastics. Electro-Mechanical (Motorized Schopper Type) is a reliable and cost effective model for providing the determination of tensile strength and starch of paper, paperboard and other similar material. Pulling rate is regulated through DC variable speed drive during the test through a calibrated potentiometer. 


Load Ranges : 
0-30 Kg. Or 300 N. 
0-60 Kg. Or 600 N. 


Also Available in higher load capacity models.



Spesification

SPECIFICATIONS

Measuring Range with

: 0-30 Kg. / 300 N with two range.

Load Scale graduation

: 0-5 Kg, 0-30 Kg.

In dual range

: 0-60 Kg. / 600 N with two range
  0-10 Kg., 0-60 Kg.

Elongation scale

: 0-100 mm and 0-50% at 180 mm.

Pulling Speed infinitely adjustable

: 5 to 250 mm/min

Adjustable clamping lengths:

: 0, 10, 50, 100, 180 and 200 mm.

Stroke

: 200 mm

Width of specimen

: 15 mm width non slip grip clamp for paper

The tester has a scale and a device for reading the strentch of the test piece. The scale is graduated in percent of test span of 180 mm with a accuracy 0.1 percent.

The 

pendulum

 is provided with internchangeble dead weight for the selection of measuring scale.

Pulling rate is regulated through DC variable speed motor during the test through a calibrated potentio meter.

Power supply

: 220V, 1-Phase 50 Hz

Applicable Standards

:TAPPI 481
  SCAN P-16
  ISO 1924

EXTRA OPTIONS:

i. Non-standard clamps
ii. Zero span jaw for fibre orientation/Bonding test.
iii. Finch device for wet tensile test.
iv. Precision test strip cutter for cutting width 15 mm.
v. Calibrated check weights

 

Shipping Data

Ordering Data

 

Net Weight

Model No.

 

Gross weight

Voltage

 

Dimension

Frequency

Changes:
UEC products undergo continuous development. The technical data in this catalogue are therefore subject to change

Inquiry

Name :
Company :
Address :
Email :
Handphone :
Subject :
Product Name :
Product Type :
Message :
   

Video

Tidak ada video untuk produk ini

Testimoni


Artikel Terkait dengan Produk AU - 1005 A TENSILE STRENGTH TESTER (Electro-Mechanical)


NEWSLETTER

 

TESTIMONIALS

B2TKS

B2TKS
Sangat jarang perusahaan seperti ini di Indonesia!  Mereka terus-menerus mengikuti perkembangan inovasi engineering test & measurement, “nyambung” berdiskusi teknis dan berpengalaman, memiliki visi pengembangan teknologi pengukuran, pengujian, inspeksi dan monitoring.(Dr.-Ing. Ir. May Isnan - NDT Specialist B2TKS-BPPT)

Chevron

Chevron
Tim kerja Alat Uji dapat diandalkan. Sangat bagus dalam implementasi di lapangan. Secara umum kami puas dengan services nya!(Andre - HSE Chevron)

BPPT

BPPT
Saya baru sekali ini bertemu perusahaan engineering yang eksis seperti ini di Indonesia.  Sangat terbantu dengan solusi yang diberikan, sangat memuaskan!(Muksin Saleh, ST., MT - Fuel Conversion and Pollution Control Specialist, B2TE - BPPT)

BALITBANG

BALITBANG
Sistem monitoring yang disuplai oleh Alat Uji adalah yang tertinggi ratingnya sampai dengan saat ini dibandingkan sistem lain yang pernah kami miliki, Dengan sistem monitoring dari Alat Uji, Pengujian kami jadi lebih terkontrol karena ada visualisasi di sistemnya. (Gatot Sukmara - Badan Penelitian dan Pengembangan, Departemen Pekerjaan Umum)

 
Alat Uji Alat Uji Alat Uji Alat Uji Alat Uji Alat Uji